Hab mir jetzt mal meine Boot-Sequence ausgeben lassen und hab sie mal ein wenig gekürzt für euch
Mir ist da was aufgefallen was bestimmt nicht so richtig ist aber ich habe null Ahnung warum und wieso das so ist...
Ich habe zusätzlich zu den 2Ports on Board noch eine USB2.0 4Port PCI-Erweiterung und ein USB 1.1 4Port-HUB angeschlossen. Ich würde jetzt erstmal so vorgehen alle Geräte aus zu stöpseln bis auf den Printer und dann mal sehen obs evt. klappt....
.
.
.
usb.c: registered new driver usbdevfs
usb.c: registered new driver hub
ehci-hcd 00:0b.2: VIA Technologies, Inc. USB 2.0
ehci-hcd 00:0b.2: irq 11, pci mem e4956f00
usb.c: new USB bus registered, assigned bus number 1
PCI: 00:0b.2 PCI cache line size set incorrectly (32 bytes) by BIOS/FW.
PCI: 00:0b.2 PCI cache line size corrected to 64.
ehci-hcd 00:0b.2: USB 2.0 enabled, EHCI 0.95, driver 2003-Jan-22
hub.c: USB hub found
hub.c: 4 ports detected
usb-uhci.c: $Revision: 1.275 $ time 18:27:45 Mar 17 2003
usb-uhci.c: High bandwidth mode enabled
usb-uhci.c: USB UHCI at I/O 0xd000, IRQ 11
usb-uhci.c: Detected 2 ports
usb.c: new USB bus registered, assigned bus number 2
hub.c: USB hub found
hub.c: 2 ports detected
usb-uhci.c: USB UHCI at I/O 0xcc00, IRQ 11
usb-uhci.c: Detected 2 ports
usb.c: new USB bus registered, assigned bus number 3
hub.c: USB hub found
hub.c: 2 ports detected
usb-uhci.c: v1.275:USB Universal Host Controller Interface driver
uhci.c: USB Universal Host Controller Interface driver v1.1
usb-ohci.c: USB OHCI at membase 0xe4958000, IRQ 11
usb-ohci.c: usb-00:02.3, Silicon Integrated Systems [SiS] 7001 (#2)
usb.c: new USB bus registered, assigned bus number 4
hub.c: USB hub found
hub.c: 3 ports detected
usb-ohci.c: USB OHCI at membase 0xe495a000, IRQ 11
usb-ohci.c: usb-00:02.2, Silicon Integrated Systems [SiS] 7001
usb.c: new USB bus registered, assigned bus number 5
hub.c: USB hub found
hub.c: 3 ports detected
mice: PS/2 mouse device common for all mice
hub.c: new USB device 00:02.3-1, assigned address 2
hub.c: USB hub found
hub.c: 4 ports detected
hub.c: new USB device 00:0b.0-1, assigned address 2
usb.c: USB device 2 (vend/prod 0x3f0/0x604) is not claimed by any active driver.
hub.c: new USB device 00:0b.0-2, assigned address 3
usb.c: USB device 3 (vend/prod 0x67b/0x2303) is not claimed by any active driver.
hub.c: new USB device 00:0b.1-2, assigned address 2
usb.c: invalid descriptor length of 0
usb.c: unable to get device 2 configuration (error=-22)
hub.c: new USB device 00:0b.1-2, assigned address 3
usb.c: invalid descriptor length of 0
usb.c: unable to get device 3 configuration (error=-22)
.
.
.
usb.c: registered new driver usblp
printer.c: Disabling reads from problem bidirectional printer on usblp0
printer.c: usblp0: USB Unidirectional printer dev 2 if 0 alt 1 proto 2 vid 0x03F0 pid 0x0604
Statistik: Verfasst von Gast — So Aug 24, 2003 19:35
]]>
]]>
]]>
]]>